![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
Application
Vacuum dryer is suitable for drying heat sensitive raw materials that can decompose and polymerize and metamorphose at high temperature. It is wide used in pharmaceutical, chemical, foodstuff and electronic industries.
Principle of work
It is well known that vacuum drying is to put raw material to the state of vacuum for heating and drying. If use vacuum to take air and humidity out, the dry speed will be faster.
Note: If use condensator, the solvent in raw material can be recovered. If use SK series water ring vacuum pump or ZSWJ series hydraulic inject vacuum pump sets, condensator can not be used and the investment could be saved.
Features
Under the condition of vacuum, the boiling point of raw material will decrease and make the pushing force become greater. Therefore for a certain amount of heat radiation, the conducting area of evaporator can be saved;
The heat source for operation of evaporation may be Iow pressure steam or surplus heat steam;
The heat loss of evaporator is less;
Before drying, the treatment of disinfection may be.
| Name\specification | YZG-600 Φ×L | YZG-800 Φ×L | YZG-1000 Φ×L | YZG-1400 Φ×L | FZG-15 L×W×H |
| inside size of chamber (mm) | 600×976 | 800×1274 | 1000×1527 | 1400×2054 | 1500×1400×1200 |
| size of chamber (mm) | 1153×810×1020 | 1700×1040×1335 | 1693×1190×1500 | 2386×1657×1920 | 1513×1924×2060 |
| layers of baking shelf | 4 | 4 | 6 | 8 | 8 |
| layer of baking shelf (mm) | 81 | 82 | 102 | 102 | 122 |
| size of baking shelf (mm) | 310×600×45 | 460×600×45 | 460×640×45 | 460×640×45 | 460×640×45 |
| number of baking disk | 4 | 8 | 12 | 32 | 32 |
| permitted pressure inside the pipe of baking shell(Mpa) | ≤0.784(8kgf/cm 2 ) | ≤0.784 | ≤0.784 | ≤0.784 | ≤0.784 |
| temperature inside chamber() | ≤150 | ≤150 | ≤150 | ≤150 | ≤150 |
| vacuum in idle inside chamber | ≤30 | ||||
| when vacuum is 30 torr and the heating temperature is 1100C,vaporized rate of water(kg/m 2. h) | 7.2 | ||||
| if use condensator,type and power of vacuum pump(kw) Â | 2X-15A 2kW | 2X-30A 3kW | W3 5.5kW | W3 7.5kW | 2X-70A 7.5kW |
| if not use condensator,type and power of vacuum pump(kw) | SK-0.8 2.2kW | SK-3 5.5kW | SK-3 5.5kW | SK-3 7.5kW | SK-3 7.5kW |
| weight of drying chamber(kg) | 250 | 600 | 800 | 1000 | 2100 |
LINA Extrusion Pelletizer
Most of the polymer must be kneaded and then granulated before it is made into a final product. Sorted by pelletizing ways, LINA rubber & plastic granulator can be divided into four categories: 1. Hot-cutting and air-cooling pelletizing method. 2. Under-water granulating method. 3. Water-strand extrusion method. 4. Water-ring granulation method. LINA pelletizer can meet the granulation needs of high-viscosity and low viscosity rubber and plastic materials, as well as some new materials and chemical additives.
LINA Die Surface Hot Cutting Pelletizing Machine
LINA`s die surface hot cutting and air cooling granulating machine is suitable for polymers that are sensitive to heat and long residence time, such as PVC, TPR, PE, cross-linked PE and so on. The flow path of the polymer from the extruder to the pelletizing port should be kept as short as possible with minimal heat. When polymer is extruded through the die surface, the rotating blade cuts the extruded materials into particles. After the pellets are cut, they are removed from the rotary blade and caught by cooling air circulating in the pelletizing room. The air stream preliminary cools the surface of the pellets and takes them out of the pelletizing room and sends them to the cooling zone.
Assembly Ling Diagram of LINA Die Surface Hot Cutting Granulator
Advantage of LINA Pelletizing Line
1. The unit has the whole unit process chain, sound and light failure alarm and fast lock fault point and other control functions. All parts that are in contact with the material are made of stainless steel.
2. High accuracy of temperature control system to ensure the temperature sensitivity of the material.
3. It adopts the drop type separating method after cutting process, to avoid Particle agglomeration and ensure particle cooling.
4. Feeding system of the pressing machine adopts heater and reversing device to solve problem of power outage, material crash and cleaning.
5. Especially, the barrel and die head adopts advanced foreign techniques to ensure and control the dangerous occurred when the pressure is uncontrollable. The honeycomb filter plate is easy to clean and quickly change the mesh and the die head t easy to leak.
6. The hoist adopts automatic return technology to ensure the working efficiency.
7. The technological combination of dual-pull forced feeder and single screw not only meet the high requirement of secondary continuous mixing, but also solve the problem of time and power consuming of traditional working process.
Specifications of LINA Extrusion Granulating Line
|
Name |
Mode |
Capacity of Kneader |
Screw length to diameter ratio |
Screw diameter |
Dimension |
|
LINA Extrusion Pelletizing Line |
LN-10/70 |
10L |
12:01 |
70mm |
2200*1000*1150 |
|
LN-10/75 |
10L |
12:01 |
75mm |
2650*1100*1250 |
|
|
LN-35/100 |
35L |
12:01 |
100mm |
3800*1090*1690 |
|
|
LN-55/120 |
55L |
12:01 |
120mm |
3800*1090*1690 |
|
|
LN-75/135 |
75L |
12:01 |
135mm |
3850*2350*3280 |
|
|
LN-110/150 |
110L |
12:01 |
150mm |
5100*2000*1500 |
|
|
LN-110/165 |
110L |
12:01 |
165mm |
5100*2000*1500 |
Hot Cutting Extrusion Pelletizer
Hot Cutting Pelletizer,Hot Cutting Pelletizing Line,Hot Cutting Pelletizing Machine,Plastic Hot Cutting Granulator
LINA Machinery Industrial Co.,Ltd , http://www.linakneader.com